Two component waterborne lacquer

2021-04-22 409

Recommended products



category
Product nameScope of application
Back coverTwo component waterborne sealerSeal wood grease and odor
Middle coatWaterborne two component transparent primerSuitable for all kinds of plates
Middle coatWaterborne two component white primerSuitable for all kinds of plates
TopcoatWaterborne two component transparent topcoatSuitable for all kinds of plates
curing agentcuring agentUse with water-based two-component series


Product characteristics



♦ High hardness

♦ Strong adhesion

♦ Scratch resistance

♦ Low odor product formula, fresh and pleasant smell


Product application


[construction method] brushing and spraying

[construction ratio] paint: clear water = 100:0-20

[construction conditions] temperature ≥ 8 ℃, relative humidity ≤ 80%

[construction method]

1. Before the construction, the paint should be fully mixed according to the proportion, and it should be kept for 10 minutes after filtration, and then used after the bubble disappears.

2. Construction method: add 5 ~ 10% water into paint to dilute. After drying completely, set aside.

3. Application method of other layers: the next layer can be applied after the upper layer of paint is completely dried and polished with 600-1000 mesh sandpaper. The coating should be applied evenly to avoid the thickness difference

Avoid sagging and foaming.

4. Cleaning of construction tools: in case of brush coating, please put the brush in the water bucket to prevent the brush from hardening. Clean the brush with clean water immediately after use, so as to prevent the mixing of solidified particles on the brush during re coating

If it is spraying, please clean the spray gun immediately.

5. Construction environment requirements: the construction environment should have good ventilation conditions, the temperature should not be lower than 8 ℃, and the relative humidity should be less than 80%. Attention should be paid to the dust pollution on the paint film at the construction site.


[paint film maintenance]

1. The longer the drying time, the better the performance.

2. Under the condition of 25 ℃ and 70% relative humidity, the surface can be dried for 8-15 minutes, and then slightly abraded after 120 minutes. After 14 days, water resistance, wear resistance and chemical resistance were achieved.


[precautions]

1. In the process of dilution with water and construction, there will be slight milky white phenomenon, and the film will be transparent after drying, so it will not affect the construction effect.

2. Because this product has the characteristics of quick drying, it may dry on the edge of the brush in the long-term construction process, which is easy to produce particles. Therefore, it is required to dry the brush with water every 15 minutes during the construction process

Clean once.

3. Keep good ventilation of construction environment to accelerate drying.


[construction taboo]

1. This waterborne paint can only be diluted with clean water.

2. It should not be mixed with other chemical solvents or oil-based diluents.

3. Construction environment requirements: the construction environment shall have good ventilation conditions, the temperature shall not be lower than 8 ℃, and the relative humidity shall be less than 80%. Attention shall be paid to the dust pollution on the paint film on the construction site.

4. This product is harmless to human body, but it is not easy to clean after drying. If it touches the skin and eyes, it should be washed with water in time.

5. This product is suitable for indoor wooden products, but it is not recommended to be used on tabletop and floor.

6. If it is brushing, please use the thin brush process. If it is a new brush, soak it in high concentration detergent water for 24 hours, and then use it after washing, otherwise particles will be produced.

7. If there are particles in the construction process, please filter the paint and replace the brush.

8. If the product is used on the old paint, use sandpaper to polish it, especially the old PU paint.

9. In case of high humidity weather (relative humidity ≥ 80%) or rainy days, please do not apply, otherwise the drying speed is very slow and causes coating defects such as poor adhesion.

10. Winter construction, if the temperature is lower than 8 ℃, please do not apply, otherwise the coating is seriously bad.

11. If the paint is not used up, please keep it airtight and keep it out of the reach of children and other irrelevant personnel.


[commitment]

1. Water is used as dispersing medium, environmental protection, low odor, no heavy metal toxicity, no hazardous substances release.

2. There will be no negative impact on the construction at home, office or business as usual.

3. After the decoration is completed, you can live immediately.

4. If your home or office furniture is very irritating, you can use this product to brush the interior surface of the furniture for two to three times to seal.